Recent News
How To Install A Metal Garage Door Properly?

Newer doors are more secure and easy to use than their predecessors. Install a new garage door using these step-by-step instructions.

The weight of an older double garage door can range from 250 to 450 lbs, depending on the model. A combination of heavyweight and worn-out parts contributes to many garage door-related injuries in older homes. However, most people enter and depart their houses by the garage door, as opposed to the formal entrance.

Installing New Garage Doors

New metal garages doors provide curb appeal and update the exterior of your house, provide a great return on investment, improve your property’s overall safety, and improve your daily convenience. However, if you’re a handyman and want to save some money, you can install your new garage door yourself in just one day if you’re a full-service garage door retailer. The service includes:

  • Delivering the new garage door.
  • Disassembling and disposing of the old garage door.
  • Installing the new garage door.

Release The Tension

Before working on the garage door, you’ll need to relieve the tension in the torsion spring. The first step is to secure the torsion spring shaft using adjustable locking pliers.

To loosen or tighten the spring winding cone, insert a steel rod into one of the four holes.

Squeeze down on the rod while releasing the set screws retaining the winding cone in place.

One quarter turns at a time, tighten or loosen the spring using the steel rods and using one rod to hold the cone stable and the second rod to spin it after the first rod withdraws the alternate the two rods until you reach the end.

Disconnect the Opener and Door

Then, remove the current garage door opener from the door. As you work your way down the panels, begin by removing the hinges that link the top panel to the bottom panel. When working with glass, use caution. Disconnect the track from the doorframe by unscrewing or unbolting it.

Install the Door Panels

You may now begin the process of installing your new door. Ensure that the bar centers on the board before moving it around it. Begin by drilling pilot holes, then screw the bar in place.

Attach hinges to each panel’s top. As a result, many new doors come with pre-drilled pilot holes. Place the bottom panel into the opening of the door and close the door. Before attaching the following tile, make sure it’s level.

Secure the Hinges

Placing the wheels into the side hinges and the top/bottom axle supports. Starting with the vertical tracks, add brackets. To be sure you’re putting the shelves correctly, see your instruction manual.

Then, put the brackets against the wall and check that the wheels are correctly set on the track. To begin with, link a door wire to the bottom panel axle support’s hook before attaching the bottom bracket.

Attach Spring Assembly To Track

Affix them to track and assemble components to support the spring assembly. Consult the instruction manual to ensure that you’re placing the body in the correct location.

Fix one end of the track to the ceiling bracket and the other to the vertical component you placed previously. Make sure you reuse the original door’s ceiling supports.

Bolt The Tracks Together

You will need to attach a horizontal track to the door’s vertical path. Be sure the door fits properly and lines up nicely before tightening the bolts.

To align the horizontal track with the vertical way, drill a hole in the flat track. Where to drill a hole may be determined by looking at where the steep path has holes drilled into it.

Fasten the rails together using bolts. When using bolts, be sure to use the right size: if the head is too large, it will impede the fence.

Install the Springs

Mark the door header in the middle of the opening. The spring support will be attached later. Using the spring anchors, attach springs to the spring locking cone.

Install Torsion Rods

Side header brackets have openings for torsion bars. Assemble the center header bracket by attaching it to the header’s center mark. Securing the assembly may require adjusting the assembly’s middle to level it.

Attach the Cable

It’s a good idea to bring the wire up from underneath and link it to both pulley wheels. Make sure that you turn it so the slack is tightened over the pulley on the door side of the vehicle. Using the header bracket, slide the wheel into place and tighten it firmly.

Tighten the rod outside of the bracket using a pair of locking pliers. You’ll be able to tighten the springs without worrying about the rod twisting as a result.

Conclusion

It might be dangerous for homeowners who have no prior expertise with this sort of operation. A metal garage kits with a torsion spring system should not be adjusted or removed since the springs are under tremendous stress, which makes them unsafe.

Leave a Reply